机械磨抛对CdZnTe薄膜阻变特性的影响

采用磁控溅射法在ITO玻璃上制备了CdZnTe薄膜,探究机械磨抛对CdZnTe薄膜阻变特性的影响。通过对XRD图谱、Raman光谱、AFM显微照片等实验结果分析阐明了机械磨抛影响CdZnTe薄膜阻变特性的物理机制。研究结果表明,磁控溅射制备的薄膜为闪锌矿结构,F43m空间群。机械磨抛提高了CdZnTe薄膜的结晶质量;CdZnTe薄膜粗糙度(Ra)由磨抛前的3.42 nm下降至磨抛后的1.73 nm;磨抛后CdZnTe薄膜透过率和162 cm^-1处的类CdTe声子峰振动峰增强;CdZnTe薄膜的阻变开关比由磨抛前的1.2增加到磨抛后的4.9。机械磨抛提高CdZnTe薄膜质量及阻变特性的原因可能是CdZnTe薄膜在磨抛过程中发生了再结晶。     

SnSxSe2-x单晶纳米片的可控制备与表征

锡二硫族化合物可以通过改变硫和硒的含量来连续调控三元合金材料的带隙、载流子浓度等物理化学性质,在电子和光电子器件应用上具有巨大的潜力。本文采用化学气相沉积(CVD)技术可控地制备了不同元素组分的SnS_xSe_2-x(x=0,0.2,0.5,0.8,1.0,1.2,1.5,1.8,2.0)单晶纳米片。采用扫描电子显微镜(SEM)、原子力显微镜(AFM)、能量色散X射线光谱(EDS)、透射电子显微镜(TEM)以及拉曼光谱等手段对SnS_xSe_2-x纳米片进行了综合表征。结果表明本方法成功实现了元素百分比可调的SnS_xSe_2-x单晶纳米片的可控制备。重点研究了依赖于元素百分比的SnS_xSe_2-x的拉曼特征谱,实验结果与基于密度泛函理论(DFT)的第一性原理计算得到的SnS_xSe_2-x的拉曼仿真谱高度吻合,理论计算结果较好地诠释了实验拉曼光谱发生变化的原因。本研究提供了一种元素百分比可调的三元SnS_xSe_2-x单晶纳米片的可控制备方法,同时对锡二硫族化合物的明确、无损识别提供了方案。     

石英晶体板非线性高频振动的拓展伽辽金法分析

针对考虑几何和材料非线性的石英晶体板厚度剪切振动和弯曲振动的方程组,利用扩展伽辽金法对该方程组进行转化和求解,分别获得了强烈耦合的厚度剪切振动模态和弯曲振动模态的频率响应关系,绘制了不同振幅比和不同驱动电压影响下的频率响应曲线图。数值计算结果表明可以选取石英晶片的最佳长厚比尺寸来避免两种模态的强烈耦合。驱动电压的变化将引起石英晶体谐振器厚度剪切振动频率的明显改变,必须将振动频率的漂移值控制在常用压电声波器件的允许值之内。扩展伽辽金法对石英晶体板非线性振动方程组的求解为非线性有限元分析和偏场效应分析奠定了基础。     

单层MXene纳米片Ti2N电磁特性的过渡金属(Sc、V、Zr)掺杂效应

二维材料MXene纳米片由于具有较大的比表面积和较高的电子迁移率而受到广泛的关注。本文采用基于密度泛函理论的第一性原理计算,对单层MXene纳米片Ti₂N电磁特性的过渡金属(Sc、V、Zr)掺杂效应进行了系统研究。结果表明,所有过渡金属掺杂体系结合能均为负值,结构均稳定;其中Ti₂N-Sc体系的形成能为-2.242 eV,结构更易形成,且保持稳定;掺杂后Ti₂N-Sc、Ti₂N-Zr体系磁矩增大;此外,Ti₂N-Sc体系中保留了较高的自旋极化率,达到84.9%,可预测该体系在自旋电子学中具有潜在的应用价值。     

Piezoelectric Nanogenerator Based on Electrospun Cellulose Acetate/Nanocellulose Crystal Composite Membranes for Energy Harvesting Application

Nanogenerators, as the typical conversion of mechanical energy to electrical energy devices, have great potential in the application of providing sustainable energy sources for powering miniature devices. In this work, cellulose acetate/cellulose nanocrystal(CA/CNC) composite nanofiber membranes were prepared by electrospinning method and then utilized to manufacture a flexible pressure-driven nanogenerator. The addition of CNC not only increased the content of piezoelectric cellulose I crystallization but also strengthened the mechanical deformation of the nanofiber membranes, which could greatly enhance the piezoelectric performance of CA/CNC composite membranes. The CA/CNC composite nanofiber membrane with 20%(mass fraction) of CNC(CA/CNC-20%) showed optimal piezoelectric conversion performance with the output voltage of 1.2 V under the force of 5 N(frequency of 2 Hz). Furthermore, the output voltage of the CA/CNC-20% nanogenerator device exhibited a linear relationship with applied impact force, indicating the great potential in pressure sensors.     

Chelating Metal Ions in a Metal-Organic Framework for Constructing a Biomimetic Catalyst Through Post-modification

Crystal engineering, as a burgeoning technology, has been widely used to construct metalloporphyrins biomimetic catalysts. Herein, a bimetallic metal-organic framework (MOF) was constructed by 4-(4-carboxyphenyl)-1,2,4-triazole ligand, Co²⁺ and Zr⁴⁺ metal ions by solvothermal reaction(named PFC-88). A N,N-chelation site was found between the two adjacent ligands in PFC-88, consequently a porphyrin-like structure was obtained through chelating Fe³⁺ in this site by post-modification, named PFC-88-Fe. The result of a single crystal X-ray technology verified that Fe ions were successfully metalated in the N,N-chelation site of PFC-88, which is assisted by the X-ray absorption near-edge structure(XANES) spectra. An o-phenylenediamine oxidation reaction was applied to assessing the catalytic activity of PFC-88-Fe, in which the absorbance increases of phenazine-2,3-diamine at λ=418 nm were recorded by absorption spectroscopy in kinetic mode, exhibiting the application potential as a biomimetic catalyst.     

一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。